NEW! SHARP LMV-50K 9" X 50" VERTICAL MILLING MACHINE W/ DVS HEAD-
|Table width: ||9"
|Table length: ||50"
Model #: LMV-50
DVS Head For:
High reliability with fewer moving parts than regular vari-speed head
Low voltage control
Large Digital RPM Display
Fully enclosed display unit
Dependable Inverter Drive System
Machine can run on single phase or 3 phase electricity
Safety device prevents machine from self starting after power failure or after emergency stop being pushed
Working Surface: 9" x 50"
T-Slot Number, Size: 3, 5/8"
Table Travel (X-Axis): 37"
Saddle Travel (Y-Axis): 12"
Quill Travel (Z-Axis): 5"
Ram Travel: 12"
Knee Travel: 16"
Spindle to Column (min-max): 6-3/4" - 18-1/2"
Spindle Nose to Table (min-max): 2-1/8" - 18"
Motor: 3 HP
Wiring Voltage: 220/440V, 3 phase, 60 Hz
Speed (Vari-speed): 60 - 4,500 RPM
Quill Feed (IPR): 0.0015", 0.003", 0.006"
Head Swivel: 360 Degrees
Head Tilt (Right to left each way): 45 Degrees
Head Tilt (Up and down each way): 45 Degrees
Dimensions & Weight:
Floor Area (WxDxH): 7' x 6-1/2' x 6-3/4'
Net Weight (approx.): 2,400 lbs
Digital Variable Speed Head
Power Feed on X Axis
3 Axis DRO
One-shot lube system
Front and rear rubber way covers
Optional Accessories: (Please call for pricing and additional information)
Power Feeds for Saddle and Knee
R-8 Collet Set
Coolant System with Chip Pan
Right Angle Milling Attachment
Riser Block (4", 7")
Auto Lube System
Halogen Work Light.
PAYMENT: Banker's check or wire transfer are preferred when dealing with transactions that exceed $1000. Any purchase of over $1000 will come with an extra 3% charge when paying through Paypal or with a Credit/Debit Card. All major credit cards are accepted.
WARRANTY: Sharp Industries warrants to the original purchaser, other than a purchaser for resale, (the “Purchaser”) that Sharp Industries machine tools shall be free of defects in materials and workmanship. For a period of one (1) year from completion of installation, Sharp Industries will, at its sole and exclusive discretion, either replace or repair any machine or part thereof defective in workmanship or material, at no charge to the Purchaser.
All warranty repairs must either be performed by Sharp Industries or MachineStation. To obtain warranty service, Purchaser must contact MachineStation. Purchaser must provide verification of the date of delivery/installation when requesting warranty service (dated installation report). Ground freight charges (UPS regular or common carrier truck) for all warranty replacement parts are paid by Sharp Industries. If machine is not operational, Sharp Industries will pay next-day air shipment charges for necessary parts weighing 100 lbs. or less. Materials or parts alleged to be defective shall be returned to Sharp Industries, at Sharp Industries’ request, transportation charges prepaid. After the warranty repair or replacement of a defective part, Sharp Industries’ warranty for such part shall continue for ninety (90) days or for the remainder of the original Limited Warranty, whichever is longer.
MACHINE USE AND SAFETY: Buyer acknowledges that the Seller has no knowledge or control over the application of these goods by the Buyer. It is the Buyer’s (user’s), responsibility to provide proper safety devices, equipment and instructions for any particular use, and to take all necessary steps to confirm to all Federal, State or Local Government Safety Standards and including OSHA.
BUYER IS RESPONSIBLE FOR SCHEDULING TRANSPORTATION OF THIS MACHINE, AS WELL AS ALL COST TO MOVE IT. IF YOU NEED HELP WITH SCHEDULING, PLEASE CONTACT US AND WE WILL ASSIST YOU. WE SHIP GLOBALLY.
This machine is listed for sale by MachineStation
located in Chino, California