CALL FOR BEST PRICE!

FEATURES:
ISO 9002 Certified: Quality Up To World Industry Standards.
Meehanite Casting: Highest Grade Of Casting Possible.
A Pair Of High Out-Put Fans: Keeps Head And 3 Hp Motor Cool, To Run Jobs For Extended Periods Without Damaging The Motor, Belts And Bearing.
Motor Shaft And Vari drive Pulleys Are Dynamically Balanced, Then Chromed For A Flawless Fit, Ground Ribs On Inside Diameter: For Smooth Speed Changes.
Motor Shaft Has An Oil Channel In The Center That Is Fed By A Grease Fitting On The Lower End: To KeepVari-Drive Pulley Moving Smoothly On The Shaft.
The Mill Uses A Roller Bearing For The Lower Support Of The Shaft: It Ensures Proper Loading, Support And Alignment It Also Prevents The Shaft From Being Distorted By The Tension Of The Belt: For Quiet, Accurate Operation At Any Speed For Years And Years.
One Shot Lubrication System: For Lubrication Of Ways And Lead Screws. (X,Y And Z Axis)
Hand Scraped Saddle And Knee: For Better Oil Retention. It Avoids Having Chips And Dirt Embed In The Knee And Damage the Sliding Surface.
Oil Groove Are Milled: For Maximum Lubrication On All Wear Areas.
Table And Saddle Backlash Is Controlled By Double Nut Design: Keeps Lead Screw In Contact With Bronze Nuts A All Times To Keep Backlash At .0008” Within 20”.
Table And Saddle Are Mounted With Thrust Bearings That Are Pre-Loaded: Eliminating End Play For Precisely Controlled Lateral Movement.
Design Uses 6 T-Bolts, 3 Per Side, Securing Them From The Outside: This Method Locks The Head Securely Resulting In Better Accuracy And Performance.
Harden & Ground & Chromed Box ways on Column & Knee for Maximum Rigidity
3 HP Motor
R-8 Spindle
Knuckle joint using bolts & circular T-slot design; Allowing head to swivel left & right, up & down
Double Nut Backlash Eliminator
Internal Lubricated Vari-Disc Design
Motor shaft end supported by bearing cap
440V Application needs an optional transformer
NOTES: SP-250A installation may reduce the X-axis travel.

STANDARD EQUIPMENT:
Power Draw Bar
3- Axis Digital Readout (quill, saddle and table)
X –axis Powerfeed
Front & Rear Rubber Way Cover
One Shot Lube System
DVS Head wired 220V (440V requires additional Transformer) Single phase is available for DVS head
Tool Kit: Machine Manual, Half-Nut Wrench, Wrench 17m, 19m, Set of 6 Allen Wrenches, Philip Screw Driver, Flat Head, Screw Driver, Oil Can, Grease Gun, Rear Way Cover Bracket, Pin For Indicator, and Can of Paint.

SPECIFICATIONS:
TABLE
Working surface: 10” x 54"
T-slot number, size: 3 Slots, 5/8"
Saddle: 26"

CAPACITY
Travels (X & Y): 33” x 16.3”
Quill Travel: 5"
Ram travel: 18.5"
Knee travel: 15.3"
Throat distance: 9.8” - 28.3"
Spindle gage line to table top: 5.375” - 16.9”

SPINDLE
Motor: 3 HP
Wiring voltage: 220/440V (please specify Voltage)
Spindle Nose Taper: R-8
Digital Variable Speed Drive: 60-4,500 RPM
Quill Feed 3 Speed (IPR): 0.0015”, 0.003”, 0.005"
Accuracy: 0.0002" TIR
Head tilt; right-to-left (each way): 90°
Head tilt up-and-down (each way): 45°

TOTAL POWER CONSUMPTIONS
220V: 3 KVA/8 amps
440V (440V Application needs an optional transformer): CALL

DIMENSIONS & WEIGHT
Floor area (w x d x h): 70" x 75" x 91.78"70" x 75"'
Weight: 3,000 lbs.

OPTIONAL ITEMS: CALL FOR PRICES
AUTOLUBE-2: Auto Lube Pump W/2 Adjustments (installed)
440T4: 380V, 440V, 575V Transformer – 3HP (for DVS machines only)
SP-250B: “Sharp” Power Cross Feed with Safety Handle (Y-Axis)
SP-250D: “Sharp” Power Knee Feed with Safety Handle (Z-Axis)
Y Axis Installation
Z Axis Installation
5000-2126 A: 6” Kurt Vise with Swivel Base D688
ACC-10TMV-R8: Right Angle Milling Attachment with Arbor
TMV-D/A: Drill Chuck & Drill Arbor
ACC-06: 6” Riser Block
Riser Block Installation
C311-TMV: Coolant System with Chip Pan at Base w/pump
ACC-R8: R-8 Collet Set of 11 (1/8”-3/4” BY 1/16”)
CK-104: Clamping Kit (52 pcs/Steel Rack)
WL-110V55W: Halogen Work light
TMV-UL: UL components upgrade (factory order)
UL compliance certificate under State of California

Specifications are subject to change without notice.

NOTE: Data is provided by the manufacturer.

WARRANTY: 1 YEAR – Parts

This machine is listed for sale by Sierra Victor Industries located in Port Orange, Florida