BUILD IN THE MID 70S

RE-INSTALLED, WITH MAJOR ELECTRICAL UPGRADE IN 1999

RAW MATERIALS: HOT ROLLED CARBON STEEL STRIP, SLIT TO WIDTH; TYPE X65 & LOWER

PIPE GRADE, API 5L/EN 10208 NORM
TABLE FROM 219.1MM TO 406.4MM

FOR THE FUNCTION OF THE LINE, THERE IS INSTALLED A SERIES OF SERVICE AUXILIARY

EQUIPMENT:
-LUBRICATION SYSTEMS
-HEAT TRANSFER COOLING SYSTEMS
-OIL EMULSION COOLANT

RAW MATERIAL, X65 AND LOWER
1) COIL OUTER DIAMETER : MAX. 1,720MM
2) COIL INNER DIAMETER : DIA. 760MM ~
3) HOP WIDTH : 508MM ~
4) HOOP THICKNESS : 4.0 ~ 14.0MM
5) SLIT COIL WEIGHT : MAX. 30 TON
PRODUCT SIZE
1) DIAMETER : MIN. DIA. 219.1MM ~ DIA. 406.4MM
2) WALL THICKNESS : MIN. 4.0MM - MAX.
3) UNIT LENGTH : MAX. 14.5 ML

LINE SPEED :MIN. 8M/MIN TO MAX. 30 M/MIN

TOOLING: 8 5/8"(219MM), 10 3/4"(273MM), 12 3/4"(324MM), 14"(356MM), 16" (406MM


EQUIPMENT SPECIFICATIONS:

ENTRY SECTION

COIL STORAGE RAMP
COIL LIFT ELEVATOR

UNCOILER, DOUBLE END, CONE TYPE
PEELER TABLE, COIL OPENER, MOTORIZED SNUBBER ROLL

PINCH ROLL

LEVELER / STRAIGHTENER, 5 ROLLS, 150 MM ROLL DIAMETER
HYDRAULICALLY OPERATED

CROP SHEAR
DRIVE MOTOR SHEAR & LEVELER: 100KW

ENTRY SIDE GUIDE ROLL

SPLICER WELDER

ULTRASONIC TESTER FOR STRIP AND EDGES
13 PROBES, (2) EDGE CONTROL, (11) STRIP SURFACE CONTROL
LOOP PIT WITH ENTRY AND EXIT CONTROL ROLLS, 30 KW MOTOR

FORMING, FIN AND SIZING SECTIONS ARE DRIVEN BY:
180KW, 195KW, & 195KW, RESPECTIVELY
DRIVEN BY THROUGH GEAR REDUCER, UNIVERSALS

FORMING SECTION
(4) FORMING STANDS, (3) FIN STANDS
(3) SIDE STANDS, IDLER
SINGLE POINT ADJUSTMENT

WELDING SECTION
EMMEDI HI FREQUENCY WELDER; 800KW AT THE WELDING ZONE, 350KHZ, 4 ROLL WELD

BOX, SCARFING
(13MM @ 20 MT/MIN)

NORMALIZATION, INDUCTION, ELPHIAC
(8) HEAT INDUCTORS, PROVIDING COMPLETE NORMALIZATION OF MATERIAL THICKNESS

13MM @ 20MT/MIN FOR 16" PIPE AT A TEMPERATURE OF 1000 DEGREES C.
FIRST (2) INDUCTION HEADS SERVE TO RAISE TO REQUESTED TEMPERATURE; 550KW,

4000HZ
SUCCESSIVE (6) INDUCTION HEADS MAINTAIN TEMPERATURE; 1200KW, 3000HZ
AUTOMATIC CONTROL, WITH (4) PYROMETER

COOLING SECTION, RUNOUT CONVEYOR

SIZING SECTION
(3) VERTICAL SIZING STANDS, DRIVEN BY (3) DC MOTORS
(3) SIDE STANDS, IDLER
TURKSHEAD

CUTOFF SECTION
FLYING CUT-OFF SAW: ROTARY DISK CUT TYPE

RUN-OUT CONVEYOR

FINISHING LINE
DOUBLE END BEVELING FINISHING MACHINE
HYDRAULIC CLAMPING
TRANSFER TABLES, ROLLER CONVEYORS

HYDROSTATIC TESTER
TRANSFER TABLES, ROLLER CONVEYORS, 8"-16" DIAMETER RANGE


ELECTRICAL UPGRADE IN 1999, SIMA CONTROLS

This machine is listed for sale by National Machinery Exchange Inc located in Newark, New Jersey