(419) 872-2364 - [email protected]

Tube Mill Plant - Slitting Line & 2 Tube Mills, Stock #3463

UTUBE NUMBER: 3463

TUBE PLANT CONSISTING OF:
Slitting Line PAXSON, 52″ x .250″ x 50,000 Lbs.
Tube Mill Line (#08) ABBEY/MCKAY, 16″ Roll Space, 3.25″ Shaft Diameter, High Frequency Welder
Tube Mill Line (#10) MCKAY, 20″ Roll Space, 4″ Shaft Diameter, High Frequency Welder
Tube Mill (#03) 33″ Roll Space, 7.5″ Shaft Diameter

PAXSON SLITTING LINE:
SPECIFICATIONS:
Maximum Strip Width: 52″
Maximum Strip Thickness: .25″
Coil Weight: 50,000 Lbs. Maximum

EQUIPPED WITH:
(1) PAXSON Uncoiler with Hold Down
Maximum Coil Width: 48″
Coil I.D. Range: 19″ – 22″
Hydraulic Expansion
Feed up Drive

(1) Entry Coil Car, 48″ (Rail Mounted)

(1) Infeed Table with Pinch Rolls

(1) PAXSON Slitter Head
52″ Wide x 8″ Arbor
S/N 11400 744 73

(2) 40 HP Drive Motors

(1) Exit Table

(1) PAXSON Driven Recoiler with Overarm Separator
S/N 11429-744
25 HP Motor
Coil Push Off

(1) Exit Single Arm Turnstyle with Push Off

(1) Lot of Knives, Spacers, Rubbers, Crate of Gears

VIDEO: Watch Video of this machine running at: https://www.youtube.com/watch?v=PJp6Z2XLJ_A&feature=youtu.be




TUBE MILL LINE (#08) ABBEY / MCKAY (RUNNING):
ENTRY EQUIPMENT:
(1) Single Uncoiler with Hold Down
(1) Shear & Weld Table

FORMING MILL:
(1) Entry Table
(4) Driven Breakdown Stands
(4) Driven Fin Stands
(6) Idle Side Roll Stands

WELDING SECTION:
(1) 5-Roll Weld Pressure Unit
(1) THERMATOOL High Frequency Contact Welder
(1) Single Scarfing Unit
(1) Chip Winder
(1) Idle Side Roll Guide
(1) 6′ Coolant Zone with Idle Side Roll

SIZING MILL:
(3) Driven Sizing Stands
(3) Idle Side Roll Stands
(1) 4-Roll Turkshead

ABBEY / ENCO HYDRAULIC CUT-OFF:
(1) 30′ Runout Table

ROLL TOOLING:
Squares & Rectangles: (1″ x 2″), (1.5″ x 1.5″), (1.62″ x 1.62″), (1″ x 2.5″), (1.5″ x 2″), (1.75″ x 1.75″), (1″ x 3″), (2″ x 2″), (2.06″ x 2.06″), (2.12″ x 2.12″), (2″ x 2.25″), (2.17″ x 2.17″), (2″ x 3″), (2.5″ x 2.5″)

ELECTRICAL:
50 HP Motor
Push Button Controls
Drive Panel

VIDEO: Watch Video of this machine running at: https://www.youtube.com/watch?v=O6nhx731FzI&feature=youtu.be



TUBE MILL (#03):
ENTRY EQUIPMENT:
(1) Single Uncoiler with Hold Down

FORMING MILL:
(4) Driven Breakdown Stands
(3) Driven Fin Stands
(5) Idle Side Roll Stands

WELDING SECTION (No Welder):
(1) Weld Pressure Unit
(1) 6′ Coolant Zone

SIZING SECTION:
(2) Driven Sizing Stands

60 TON ROUSSELLE #6B-60 OBI PUNCH PRESS:
(1) TALLYRAND Cabinet, Length Control
(1) 30′ Runout Table

ROLL TOOLING:
Squares & Rectangles: (1.5″ x 4″), (2″ x 4.5″), (2.5″ x 4″), (1.37″ x 5.12″), (2″ x 5″), (3″ x 4″), (3.5″ x 3.5″), (2.5″ x 5″), (3″ x 4.5″), (3.5″ x 4″), (2″ x 6″), (3″ x 5″), (4″ x 4″)

ELECTRICAL:
100 HP Motor
Push Button Controls

This machine is listed for sale by Universal Tube & Rollform located in Perrysburg, Ohio